Produse pentru omnifix luer soloname (13)

Consilex Barrier-A Solution of special modified silicone resins, dispersed in water, hydrophilic in the application phase, water-repellent and water-repellent after reaction with atmospheric carbon dioxide, for the preparation of water-repellent solutions for the creation of chemical barriers against capillary rising in masonry. Formation, by injection, of horizontal chemical barriers for stopping capillary rising damp in building renovation and damp brickwork; water repellent and reinforcing treatment with slightly alkaline porous building materials: bricks, tiles, terracotta and crude ceramic materials, etc. Remove the existing plaster, only if necessary, up to at least one metre above the line of evident damp. Draw a line parallel to the outside kerb or inside flooring, at a distance of about 10-15 cm from the same. Prepare drilling points at 12 cm distance from one another on the traced line. The inclination of the holes should be about 20° down. The depth of the holes should be approximately 4/5 the thickness of the wall to inject. The drill bit to be used must have a diameter of 18-20 mm. Once the holes are finished, the dust produced by drilling is required to be eliminated. The product can be diluted with demineralised water or with a hardness less than 35°F up to a maximum of 15-20% (it is recommended for use preferably without dilution). Proceed with the pure product or with the solution obtained, with low pressure injections by airless pump (manual or electric), directly into the designated holes in the masonry. Consumption may vary depending on the characteristics of the masonry and its thickness. By way of example, for 50 cm thick masonry, the indicative consumption of the aqueous solution is between 17 and 20 l/m. Consilex Barrier-A requires an adequate and as lengthy an exchange as possible with the atmosphere, for the hydrophilic-hydrophobic transformation: schedule an adequate waiting time prior to sealing the injection holes and coating the brickwork. It is advisable to create the chemical barrier with Consilex Barrier-A- when work commences at the construction site and to close the injection holes a few days before ends. Apply on porous media, with pH not exceeding 8. Protect glass and aluminium surfaces from contact with the product. From 3.5 to 4.0 litres of Consilex Barrier-A per linear metre of 10 cm thick masonry. Calculate the consumption in proportion to the thickness of the masonry to be restored. Plastic can 10 l - Plastic can 25 l - Plastic can 5 l

Formulated with organic acid technology (OAT), it is a long-lasting concentra ted cooling fluid that ensures that the engine operates at ideal operating temperature in all four seasons. The specially developed green design is ethylene glycol based antifreeze and does not contain nitrite, amine, phosphate, silicate and borate. Before use in all climatic conditions ta provide optimum performance in the radiators of motor cooling systems, dilute with 50 % pure water.

Battery Cycle Count A typical cell phone battery goes through approximately 500 cycles before retaining at least 80% of its original capacity. Made from new materials, our batteries have zero cycles, ensuring the maximum number of cycles you can use. Zero Cycle Count, so you have the maximum amount of cycles remaining. Lithium-Ion Polymer technological materials Strict QC test Less than 1% failure rate 12 Months Warranty

LUXLINE - MODEL SI SI/F numer artykułu:SI/F

Durch Volumenstromüberwachungen werden die Luftströmungen überwacht. Sie enthalten einen kalorimetrischen Sensor im Schutzgehäuse. Es sind Auswerteelektronik, Ausgangsrelais, Einstellpotentiometer und LEDs, sowie ein Zeitrelais zur Anlaufüberbrückung integriert. Volumenstromüberwachungen sind in den Nennweiten 75-400 mm Anschlussdurchmesser lieferbar. Mit den Anschlussvarianten Flansch und Muffe erhältlich. Standardmäßig in den Werkstoffen PPs und PVC lieferbar. Sonderwerkstoffe auf Anfrage. Weitere Informationen erhalten Sie auf unserer Website oder direkt auf Anfrage. Deutschland: Deutschland

Spécifique pour les produits difficiles à démouler, par exemple riches en sucre et en protéine. Excellent pouvoir anti-adhérent. Viscosité :700 à 1100 mPa.s (25°C) Valeur d’iode:± 80 Point de fumée:230 °C POIDS SPECIFIQUE:920 kg/m3 (20°C) Formats disponibles:10L – GRV 1000L

Das Premium-Glasfalz-Silikon

OLIK HM 22 - 1000L OLIK HM 22 - 208L OLIK HM 22 - 20L Gamme:OLIK Secteur:HYDRAULIQUE Code EAN/CTIN:3701344705756

Suitable for untreated or oiled oil and cork indoors. Suitable for all common or factory oils for preservation and treatment. Inoffensive to cobalt and oxime allergy sufferers. Our Product has a pleasant odor due to the exclusive use of high-quality resources.

Roulettes pivotantes à oeil roue jante polyamide bandage caoutchouc gris non tachant. Supports acier embouti zingué. Du diamètre 80 au au 200 mm De 50 Kgs à 205 Kgs de charge utile.

Construction Primer C

Spécifique pour les produits riches en sucre et/ou protéine. Protège le matériel de cuisson. Parfaitement adapté aux formes et platines en aluminium recouvertes ou non d’un coating. Spécifique pour les produits de longue conservation. Viscosité :± 170 mPa.s (25°C) Valeur d’iode:± 40 Indice peroxyde:Max. 3 POIDS SPECIFIQUE:920 kg/m3 (20°C) Formats disponibles:10L – IBC 1000L

Der extrem wasserbeständige Premium-Hybrid-Klebstoff